openlava – Hot Resource Manager
One of the most critical pieces of software on a cluster is the resource manager, commonly called a job scheduler. It allows users to share the system in a very efficient and cost-effective way. The idea is fairly simple: Users write small scripts, commonly called “jobs” that define what they want to run and the resources that are required, and submit it to the resource manager. When the resources are available, the resource manager executes the job script on behalf of the user. Typically this approach is for batch jobs – that is, jobs that are not interactive – but it can also be used for interactive jobs in which the resource manager gives you a shell prompt to the node that is running your job.
You have several options when it comes to resource managers. Some of them are commercially supported and some are open source, either with or without a support option. The list is fairly long, but the one I want to cover in this article is openlava.
Openlava
Platform Computing has had one of the most successful and arguably robust commercially supported resource managers, named LSF, for many years. A while ago, Platform created a cluster management tool that is now called IBM Platform Cluster Manager (PCM) [Note: Platform was acquired by IBM]. PCM is an open source package, and Platform wanted to integrate an open source resource manager with the tool. In 2007 Platform took an older version of LSF, version 4.2, and created an open-source resource manager, which they named Platform Lava or just “Lava.” It is still included in PCM today.
Not too long ago, some developers based a new resource manager on Lava, calling it openlava. Openlava has been developed to go beyond the incorrectly advertised cluster size of 512 nodes while adding functionality. Openlava has a nice mailing list, and the developers make binaries available for major distributions such as Red Hat 5 and 6, CentOS 5 and 6, and openSUSE.
Although openlava is tremendously easy to install, you have to pay attention to a few gotchas. (In my first attempt I didn’t pay attention to these.) In the next sections, I’ll walk through the installation of openlava on a cluster (the Warewulf-based cluster I’ve been writing about) and present a few configuration options that might help.
Installing openlava
The installation of openlava can proceed in several ways. You can install it on each node in the cluster, or you can install it in a shared filesystem. It works just fine in either case, but unlike many other resource managers, openlava works really well on a shared filesystem, so you can make your life a bit easier by going this route.
I installed openlava on a Scientific Linux 6.2 system using the RHEL 6 binaries. If you read the Quickstart guide on the openlava site, you will learn that this binary is installed into /opt/openlava-2.0 . For the Warewulf cluster I’m using for my testing, this works out very well because /opt is NFS-exported from the master node to the compute nodes.
The first step was to install openlava on the master node of the cluster. This is very easy to do using yum (Listing 1).
Listing 1: Installing the openlava RPM on the Master Node
[root@test1 RPMS]# yum install openlava-2.0-206.1.x86_64.rpm Loaded plugins: fastestmirror, refresh-packagekit, security Loading mirror speeds from cached hostfile * elrepo: mirror.symnds.com * epel: mirror.hiwaay.net * rpmforge: mirror.us.leaseweb.net * sl: ftp1.scientificlinux.org * sl-security: ftp1.scientificlinux.org Setting up Install Process Examining openlava-2.0-206.1.x86_64.rpm: openlava-2.0-206.1.x86_64 Marking openlava-2.0-206.1.x86_64.rpm to be installed Resolving Dependencies --> Running transaction check ---> Package openlava.x86_64 0:2.0-206.1 will be installed --> Finished Dependency Resolution Dependencies Resolved ======================================================================== Package Arch Version Repository Size ======================================================================== Installing: openlava x86_64 2.0-206.1 /openlava-2.0-206.1.x86_64 15 M Transaction Summary ======================================================================== Install 1 Package(s) Total size: 15 M Installed size: 15 M Is this ok [y/N]: y Downloading Packages: Running rpm_check_debug Running Transaction Test Transaction Test Succeeded Running Transaction Installing : openlava-2.0-206.1.x86_64 1/1 Installed: openlava.x86_64 0:2.0-206.1 Complete!
Just as a reminder, the binary I used installs openlava into the directory /opt/openlava-2.0 , which, for the test cluster, is a NFS shared filesystem. Fortunately, the design of openlava means I don’t need to install the binaries into the VNFS for my Warewulf cluster. All I really need to do is install the startup (init) scripts for openlava into the VNFS.
To make sure I had everything copied over to the VNFS I wrote a small script t(Listing 2).
Listing 2: Installing init Scripts into VNFS
cp /etc/init.d/openlava /var/chroots/sl6.2/etc/init.d/openlava cp /etc/profile.d/openlava.csh /var/chroots/sl6.2/etc/profile.d/openlava.csh cp /etc/profile.d/openlava.sh /var/chroots/sl6.2/etc/profile.d/openlava.sh cd /var/chroots/sl6.2/etc/rc.d/rc0.d ln -s ../init.d/openlava K01openlava cd /var/chroots/sl6.2/etc/rc.d/rc1.d ln -s ../init.d/openlava K01openlava cd /var/chroots/sl6.2/etc/rc.d/rc2.d ln -s ../init.d/openlava S99openlava cd /var/chroots/sl6.2/etc/rc.d/rc3.d ln -s ../init.d/openlava S99openlava cd /var/chroots/sl6.2/etc/rc.d/rc4.d ln -s ../init.d/openlava S99openlava cd /var/chroots/sl6.2/etc/rc.d/rc5.d ln -s ../init.d/openlava S99openlava cd /var/chroots/sl6.2/etc/rc.d/rc6.d ln -s ../init.d/openlava K01openlava
Only three small files are copied into the VNFS; the rest just symlinks within the VNFS. Note that the VNFS root directory is /var/chroots/sl6.2 , so you might have to change the path to your VNFS (if you are using Warewulf). If you are not using Warewulf, you have several options. You can install the RPM into the image for each compute node or, if you have compute nodes that mount the shared filesystem, you will have to make sure the above scripts and symlinks are in the image for each compute node.
After running this script, which you have to do as root, you just rebuild the VNFS (Listing 3).
Listing 3: Rebuilding the VNFS Configuration
[root@test1 ~]# wwvnfs --chroot /var/chroots/sl6.2 --hybridpath=/vnfs Using 'sl6.2' as the VNFS name Creating VNFS image for sl6.2 Building template VNFS image Excluding files from VNFS Building and compressing the final image Cleaning temporary files WARNING: Do you wish to overwrite 'sl6.2' in the Warewulf data store? Yes/No> y Done.
Before you can configure openlava, you need to create an openlava account for the openlava user. This isn’t difficult to do – just use the useradd command:
[root@test1 ~]# useradd -d /home/openlava -g openlava -s /bin/bash openlava
I put the openlava home directory in /home and created a group called openlava .
One very important point is that the openlava user has to be on each system – the master node and all compute nodes that are running openlava. On the master node, I added a user, so there are new entries in /etc/passwd and /etc/shadow that are included as “files” in Warewulf, so now I need to tell Warewulf to update its version of these files. (Note: These files are automatically pushed to the compute nodes by Warewulf when they are booted.) This is easily done with the command:
[root@test1 ~]# wwsh file sync
If you have problems getting openlava to work, then be sure to check that user openlava exists on all nodes.
One last thing to do before editing the openlava configuration files is to make sure the command . /etc/profile.d/openlava.sh is run by every user. To make things easy, I put the command in .bashrc because I’m running the Bash shell. This needs to happen for all users and root.
Now you can edit the openlava configuration. All of the files you really need to worry about are in /opt/openlava-2.0/etc and are pretty easy to edit. In the configuration files, you need to include both the master node and all compute nodes, even if you don’t want compute jobs to be run on the master node (this is an easy thing to change when you want). The first file to edit is /opt/openlava-2.0/etc/lsf.cluster.openlava which defines which nodes are part of this openlava cluster. The changes you need to make are very simple, and Listing 4 is what I use for my system.
Listing 4: Main openlava Cluster Configuration File
[root@test1 etc]# more lsf.cluster.openlava #----------------------------------------------------------------------- # T H I S I S A O N E P E R C L U S T E R F I L E # # This is a sample cluster definition file. There is a cluster # definition file for each cluster. This file's name should be # lsf.cluster.. # See lsf.cluster(5) and the "LSF Administrator's Guide". # Begin ClusterAdmins Administrators = openlava End ClusterAdmins Begin Host HOSTNAME model type server r1m RESOURCES test1 ! ! 1 - - n0001 ! ! 1 - - End Host Begin ResourceMap RESOURCENAME LOCATION # tmp2 [default] # nio [all] # console [default] End ResourceMap
The nodes that are in the openlava “cluster” are between the lines Begin Host and End Host . The first node I listed is test1 , which is my master node, and the second node, n0001 , is my first compute node. Notice that I used the defaults after the node name.
The second file I edited was /opt/openlava-2.0/etc/lsb.hosts . In this file, you can tell openlava about how many “slots” or cores your nodes have. For my cluster, the file looks like Listing 5.
Listing 5: Normal Loading of Environment Modules
[root@test1 etc]# more lsb.hosts # # The section "host" is optional. If no hosts are listed here, all hosts # known by LSF will be used by Batch. Otherwise only the hosts listed will # be used by Batch. The value of keyword HOST_NAME may be an official host # name (see gethostbyname(3)), a host type/model name (see lsf.shared(5)), or # the reserved word "default". The type/model name represents each of the # hosts which are of that particular host type/model. The reserved # word "default" represents all other hosts in the LSF cluster. # MXJ is the maximum number of jobs which can run on the host at one time. # JL/U is the maximum number of jobs belonging to a user that can run on the # host at one time. The default is no limit. # DISPATCH_WINDOW is the time windows when the host is available to run # batch jobs. The default dispatch window is always open. # Other columns specify scheduling and stopping thresholds for LIM load # indices. A "()" or "-" is used to specify the default value in a column # and cannot be omitted. # All the host names (except default) in this example are commented out, # since they are just examples which may not be suitable for some sites. # Don't use non-default thresholds unless job dispatch needs to be controlled. Begin Host HOST_NAME MXJ JL/U r1m pg ls tmp DISPATCH_WINDOW # Keywords test1 0 () () () () () () n0001 3 () () () () () () default ! () () () () () () # Example End Host # Host groups can be referenced by the queue file. Each line defines a host # group. The first line contains key words; each subsequent line contains a # group name, followed by white space, followed by the list of group members. # The list of members should be enclosed in parentheses and separated by white # space. This section is optional. # This example is commented out #Begin HostGroup #GROUP_NAME GROUP_MEMBER # Key words #group0 (host0 host1) # Define a host group #End HostGroup
To get started, just edit the lines between Begin Host and End Host . The line with the default host was already there, but I added the lines for the master node, test1 , and the first compute node, n0001 . The number in the MXJ column refers to the maximum number of jobs that can run on the host at one time. In my case, the compute node, n0001 , has only three cores, so I gave a value of 3 . I chose not to run any jobs on the master node, so I entered 0 under MXJ. If I wanted to run on the master node, I would have entered a value of 4 because I have four cores in my master node.
Booting the Nodes
Booting openlava on both the master node and the compute node is not difficult, but you have a few commands to use to make sure everything is working correctly. Because openlava doesn’t start when the master node boots, I used the service command to start it the first time:
[root@test1 ~]# service openlava start Starting daemons... lim started res started sbatchd started
I also recommend using the command service openlava start to make sure all of the daemons were started correctly. You should see something like the following:
[root@test1 ~]# service openlava status lim pid: <2707> res pid: <2709> sbatchd pid: <2711> lim mbatchd: <2718>
The numbers in the brackets are the process IDs (PIDs) for each daemon. On the master node, you should see four PIDs, which in fact is the case.
You can read a bit more about these daemons in the openlava documentation, but if you don’t want to read an architecture document, here is a quick overview:
- LIM: The openlava Load Information Manager monitors the machine’s load and sends the information to the LIM on the cluster master.
- RES: The openlava Remote Execution Server executes user tasks on remote hosts.
- sbatchd: The slave batch daemon is responsible for starting jobs, monitoring them, acting on them based on user requests (e.g., moving them or killing them), collecting their status once they terminate, and reporting it to the user.
- mbatchd: The master batch daemon is responsible for executing scheduling policies and dispatches user’s jobs based on them. This daemon will only run on the master node of the openlava cluster (i.e., it won’t be on the compute nodes).
The openlava architecture is very simple, and these four daemons interact in a very transparent way.
You should then use the lsid command to make sure the LIM deamon has started correctly:
[root@test1 ~]# lsid openlava project 2.0, Jun 8 2012 My cluster name is openlava My master name is test1
The output from this command gives you the openlava cluster name; the default is openlava . It also tells you the name of the master for the openlava cluster. In this case it’s test1 , which makes sense because I have only started the master node.
I like to do a few more checks to make sure everything is working correctly. The first is lshosts :
[root@test1 ~]# lshosts HOST_NAME type model cpuf ncpus maxmem maxswp server RESOURCES test1 DEFAULT DEFAULT 1.0 4 7363M 13999M Yes () n0001 UNKNOWN UNKNOWN_ 1.0 - - - Yes ()
You can tell the monitoring (LIM) on the master node is working because it reports the number of cores (nc pus ) correctly (4 ), and it reports the maximum memory and the maximum swap space (maxmem and maxswp , respectively).
The second command I like to use is bhosts , which lists the hosts in the openlava cluster.
[root@test1 ~]# bhosts HOST_NAME STATUS JL/U MAX NJOBS RUN SSUSP USUSP RSV n0001 unavail - 3 0 0 0 0 0 test1 closed - 0 0 0 0 0 0
You can tell that openlava is working up to this point because the master node (test1 ) reports closed , which is correct because I told openlava that it had no slots (CPUs) for running jobs. The output also says that the first compute node, n0001 , is unavail , which is correct because I haven’t started it, so the openlava daemons can’t contact it.
The next step is to boot the compute node. After it boots, you can log in and, as root, start up openlava (in fact, it might have started when it booted):
bash-4.1# service openlava start Starting daemons... lim started res started sbatchd started
The daemons start up correctly, so the first thing to do is use the command service openlava status to check the status of the daemons on the compute node"
bash-4.1# service openlava status lim pid: <1667> res pid: <1669> sbatchd pid: <1671> lim mbatchd: <>
Notice that the compute node has no PID for mbatchd . This makes perfect sense because the compute node is not the master node, so it will not be running mbatchd .
Next, I’ll check the status using lsid:
bash-4.1# lsid openlava project 2.0, Jun 8 2012 My cluster name is openlava ls_getmastername(): Cannot locate master LIM now, try later
When the compute node starts, it takes a while for all of its information to flow to the master node, which is why you see an error contacting the master node’s LIM process. If you see this error, you should wait a few minutes to see whether the compute node LIM starts communicating with the master node’s LIM. I only waited about 60 seconds and reran the command:
bash-4.1# lsid openlava project 2.0, Jun 8 2012 My cluster name is openlava My master name is test1
Now that the compute node LIM and the master node LIM are communicating, you will get a proper response (at least not an error). The output from lsid shows the correct openlava cluster name (openlava ) as well as the correct openlava master name, test1, so the LIMs are communicating correctly.
The next command to run on the compute node is lshosts :
bash-4.1# lshosts HOST_NAME type model cpuf ncpus maxmem maxswp server RESOURCES test1 DEFAULT DEFAULT 1.0 4 7363M 13999M Yes () n0001 UNKNOWN UNKNOWN_ 1.0 3 2887M - Yes ()
You can tell that the monitoring (LIM) on the compute node is working because it reports the number of cores (n cpus ) correctly (3 ), and it reports the maximum memory and the maximum swap space (maxmem and maxswp ). However, the compute node does not have any swap space, so the entry for maxswp is not listed.
The bhosts command goes one step further by listing the hosts in the openlava cluster:
bash-4.1# bhosts HOST_NAME STATUS JL/U MAX NJOBS RUN SSUSP USUSP RSV n0001 ok - 3 0 0 0 0 0 test1 closed - 0 0 0 0 0 0
The output also says that the first compute node, n0001 , is ok , whereas the status of the openlava master node is closed (since we told it not to run any jobs).
It looks like everything is running correctly, but it’s important to take a look at the openlava master node once the compute node is up and running. To do this, I will run the command lshosts and bhosts on the openlava master node (Listing 6).
Listing 6: Checking the openlava Master Node Once the Compute Node is Running Correctly
[root@test1 ~]# lshosts HOST_NAME type model cpuf ncpus maxmem maxswp server RESOURCES test1 DEFAULT DEFAULT 1.0 4 7363M 13999M Yes () n0001 UNKNOWN UNKNOWN_ 1.0 3 2887M - Yes () [root@test1 ~]# bhosts HOST_NAME STATUS JL/U MAX NJOBS RUN SSUSP USUSP RSV n0001 ok - 3 0 0 0 0 0 test1 closed - 0 0 0 0 0 0
Everything is normal at this point. The lshosts command indicates that the compute node LIM is communicating with the openlava master node LIM because the number of CPUs (n cpus ) is correct (3 ), and the maxmem number is correct (2887M ). The output from the bhosts command is also correct because the status of the compute node, n0001 , is ok , and the number of job slots, MAX , is correct (3 ).
Running Jobs
Openlava appears to be working correctly, but to be absolutely sure, I need to throw some job scripts at it. The first is a simple script to make sure openlava is passing hostnames correctly (Listing 7).
Listing 7: First Job Script
#!/bin/bash # # LSF test1 # #BSUB -P test1 # Project test1 #BSUB -n 2 #BSUB -o test1.out # output filename #BSUB -e test1.err # error filename #BSUB -J test1 # job name # for h in `echo $LSB_HOSTS` do echo "host name: $h" done
I won’t go into the details of the script because the openlava site documents it, and LSF examples are all over the web. However, because I standardized on this list of openlava “commands,” I will explain them briefly. Any line that starts with #BSUB is a directive for openlava. The directives I used in the script are:
- #BSUB -P test1 : The “project” name for the script.
- #BSUB -n 2 : Sets the number of processors needed (2 in this case).
- #BSUB -o test1.out : Sets the stdout output file from openlava to test1.out.
- #BSUB -e test1.err : Sets the stderr output file from openlava to test1.err.
- #BSUB -J test1 : Name of the job.
I submitted the job to openlava with the command:
[laytonjb@test1 TEST_OPENLAVA]$ bsub -R "type=all" < test1.script
The file test1.script is the script listed above. The command bsub is what you use to submit the script to openlava. I used the option -R "type=all" because I have a compute node that is different from the master node. Consequently, I need to tell openlava that it can use any node type, even ones it doesn’t understand, for running the job.
Listing 8 shows the two files returned by openlava, test1.err and test1.out
Listing 8: Output from First Job Script
[laytonjb@test1 TEST_OPENLAVA]$ more test1.err
[laytonjb@test1 TEST_OPENLAVA]$ more test1.out
Sender: LSF System
Subject: Job 818: Done
Job was submitted from host by user .
Job was executed on host(s) <2*n0001>, in queue , as user .
was used as the home directory.
was used as the working directory.
Started at Mon Sep 24 19:42:14 2012
Results reported at Mon Sep 24 19:42:16 2012
Your job looked like:
------------------------------------------------------------
# LSBATCH: User input
#!/bin/bash
#
# LSF test1
#
#BSUB -P test1 # Project test1
#BSUB -n 2
#BSUB -o test1.out # output filename
#BSUB -e test1.err # error filename
#BSUB -J test1 # job name
#
#
for h in `echo $LSB_HOSTS`
do
echo "host name: $h"
done
#cat pgfile
------------------------------------------------------------
Successfully completed.
Resource usage summary:
CPU time : 0.03 sec.
The output (if any) follows:
host name: n0001
host name: n0001
PS:
Read file for stderr output of this job.My apology for the length, but I think it’s important to see at least what the output files from openlava look like.
I did one more test – running a simple MPI program. It is simple code for computing the value of pi (Listing 9), built using the Open64 compiler and mpich2 (a previous article explains the environment I used).
Listing 9: Openlava Job Script for Running Sample MPI Code
#!/bin/bash
#
# Test 2 script for openlava
#
#BSUB -P test2 # Project test1
#BSUB -n 2
#BSUB -o test2.out # output filename
#BSUB -e test2.err # error filename
#BSUB -J test2 # job name
# Change to correct directory (full path)
# Not strictly necessary but a good practice
cd /home/laytonjb/TEST_OPENLAVA
# Load needed modules here
. /etc/profile.d/modules.sh
module load compilers/open64/5.0
module load mpi/mpich2/1.5b1-open64-5.0
# Write hosts to a file
for h in `echo $LSB_HOSTS`
do
echo $h >> pgfile
echo "host name: $h"
done
# Calculate the number of processors allocated to this run.
NPROCS=`wc -l < ./pgfile`
# Calculate the number of nodes allocated.
NNODES=`uniq ./pgfile | wc -l`
### Display the job context
echo "Running on host `hostname` "
echo "Start Time is `date` "
echo "Directory is `pwd` "
echo "Using ${NPROCS} processors across ${NNODES} nodes "
# Execute mpi command
mpirun -np 2 -machinefile pgfile ./mpi_pi < file1 > output.mpi_pi
# erase file with node names
rm ./pgfile
echo "End time is `date` "In the Listing 10, I show how I submitted the job, with several queries on the status of the job.
Listing 10: Submitting the MPI Job Script and Checking Its Status
[laytonjb@test1 TEST_OPENLAVA]$ bsub -R "type==any" < test2.script
Job <839> is submitted to default queue .
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
JOBID USER STAT QUEUE FROM_HOST EXEC_HOST JOB_NAME SUBMIT_TIME
839 laytonj PEND normal test1 test2 Sep 24 20:24
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
JOBID USER STAT QUEUE FROM_HOST EXEC_HOST JOB_NAME SUBMIT_TIME
839 laytonj PEND normal test1 test2 Sep 24 20:24
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
JOBID USER STAT QUEUE FROM_HOST EXEC_HOST JOB_NAME SUBMIT_TIME
839 laytonj PEND normal test1 test2 Sep 24 20:24
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
JOBID USER STAT QUEUE FROM_HOST EXEC_HOST JOB_NAME SUBMIT_TIME
839 laytonj PEND normal test1 test2 Sep 24 20:24
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
JOBID USER STAT QUEUE FROM_HOST EXEC_HOST JOB_NAME SUBMIT_TIME
839 laytonj RUN normal test1 n0001 test2 Sep 24 20:24
n0001
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
JOBID USER STAT QUEUE FROM_HOST EXEC_HOST JOB_NAME SUBMIT_TIME
839 laytonj RUN normal test1 n0001 test2 Sep 24 20:24
n0001
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
No unfinished job found
[laytonjb@test1 TEST_OPENLAVA]$ bjobs
No unfinished job foundIn the first line, I submitted the job. After that I checked on the status with the openlava bjobs command. Notice that the first check on the status of the jobs shows PEND (under the STAT column). After the job stats running, you see which “hosts” are executing the job (under the EXEC_HOST column). Finally, the no more unfinished jobs are found, so I know the job has finished. If you are interested, Listing 11 is an abbreviated listing of the output from the job, as well as the output from the code.
Listing 11: Abbreviated openlava Output from MPI Job and the Output from the Code
------------------------------------------------------------ Successfully completed. Resource usage summary: CPU time : 0.14 sec. The output (if any) follows: host name: n0001 host name: n0001 Running on host n0001 Start Time is Mon Sep 24 20:25:55 EDT 2012 Directory is /home/laytonjb/TEST_OPENLAVA Using 2 processors across 1 nodes End time is Mon Sep 24 20:25:56 EDT 2012 PS: Read file for stderr output of this job. [laytonjb@test1 TEST_OPENLAVA]$ more output.mpi_pi Enter the number of intervals: (0 quits) pi is 3.1623529411764704 Error is 2.07602875866772507E-2
Summary
A resource manager, one of the most critical pieces of software in HPC, allows systems and their resources to be shared efficiently. The resource manager discussed in this article, openlava, is based on Platform Lava, which in turn is an open-source version of an older version of Platform LSF (now called IBM Platform LSF). So, openlava has a very distinguished pedigree.
Installing openlava was very easy, even using a shared filesystem. This isn’t always the case with other resource managers, so I take this as a big benefit of openlava. You should read the installation instructions carefully and heed every word. (I didn’t the first time around.) In particular, you should pay attention to the following:
- If you don’t install openlava on each node, be sure all of the init scripts are on every node.
- Create the openlava user and make sure it is on all compute notes.
- Make sure the /etc/profile.d/openlava.sh script is on each node and is executed – even for the root user.
If you pay attention to these key issues, the installation and activation should go smoothly.
The tips I have included to make sure everything is working properly are the result of some simple mistakes I made. Hopefully they will help you as well. I also included a few configuration details I hope will help in your initial configuration. In particular, I showed how you can configure the master openlava node so it does not run jobs.
Finally, I wrote a couple of simple job scripts to show very briefly how you can write your own, including a simple MPI job. If you need more details on how to write scripts, you will find a plethora of stuff on the web, and the openlava mailing list is a wonderful place to get help.
When you think about resource managers, and you will if you run HPC systems, then openlava is a very serious contender. Take a look at it, and give it a try – it’s really easy to install, configure, and manage.
Related content
-
Warewulf Cluster Manager – Completing the Environment
Installing and configuring Warewulf on the master node and booting the compute nodes creates a basic cluster installation; however, a little more configuration to the master remains and a few other tools must be installed and configured for the Warewulf cluster to become truly useful for running HPC applications.
-
Warewulf Cluster Manager – Administration and Monitoring
In the last of this four-part series on using Warewulf to build an HPC cluster, I focus a bit more on the administration of a Warewulf cluster, particularly some basic monitoring and the all-important resource manager.
-
Warewulf Cluster Manager – Master and Compute Nodes
The Warewulf stateless cluster tool is scalable and highly configurable, and it eases the installation, management, and monitoring of HPC clusters.
-
Warewulf Cluster Manager – Development and Run Time
The Warewulf cluster is ready to run HPC applications. Now, it’s time to build a development environment.
-
Warewulf 4
Warewulf 4 is ready to help you build an HPC cluster.